Snowblower Parts Ranch King

initial installation extended explanation

This describes exactly how to proceed in order to FOXSAT HD use the full functionality of.
This "howto" explains the settings for a fixed antenna. User of a motorized system for point 3 please select "skip" and can change the settings you need from the menu.

If the settings for devices with an attached antenna cable, different from those connected with two antenna cables are wiefolgt be highlighted:

A cable: If the device is connected to an antenna feed line.

double connection: If 2 antenna cables are connected via a multi-switch to the device.

different double connection: when connected by two LNB's each a separate antenna cable to the receiver (Astra LNB to port 1 and Hotbird LNB to port 2 for example).

---

1. Language:
   Use the up and down arrow keys to select the desired language. The selected language is marked with a yellow background. To confirm, press the OK button in the middle.
   
   
2. Time Zone:
   You can run the country in which the receiver and thus set the GMT offset. Standard is Germany. If you operate the receiver in another country, you press either the down arrow key 1x or 2x highly inferior to yellow around the country. With arrow key left / right to change the country. With pressing OK, click the button "next", it goes on.
   
   
3. Connection:
   This sets the type of antenna connection. Please note here to make the right choice:
   A cable: If you connect an antenna cable
   
   
   
   • double connection:
     If you have connected 2 antenna leads a multi-switch and is therefore used two basically identical Antennzuleitungen to ICORD.
     
     
   • different double connection:
     when you connect 2 LNB's each a separate antenna cable to the receiver (Astra LNB to port 1 and Hotbird LNB to port 2 for example). Amend
     
   
   
   To the standard (one cable), just hit the up arrow key and select by law or press the left arrow button the right attitude. Press OK to the next point.
   
   
4. standard channels:
   The FOXSAT HD has a preprogrammed channel list for the Astra satellite. In this list are the most important German programs already pre-stored and a search is necessary only if the following conditions:
   
   you have a pay-TV offer (Premiere, Arena, etc.)
   you want to see all available services and can access the Complete list of channels.
   
   Please use the arrow keys left / right if you want to use this default list (If YES, the points accounts for 5 - 7) and confirm with OK.
   
   
   
5. antenna settings:
   The antenna settings are preset for a standard satellite dish without multiswitch. However, it is recommended here, the software-side reasons Diseqc 2.0 activate.
   
   Please make the point value input Diseqc Diseqc 2.0 is an A if you control only Astra and Astra is on Diseqc A. If the Astra satellite at your facility located on Diseqc B, set B is a Diseqc 2.0.
   
   Confirm your selection with the OK button.
   
   
   
6. also add satellites:
   Please press the arrow key up and OK for another satellite (eg Hotbird) added. Go away again to step 5. Make sure to choose the correct here Diseqc settings.
   
   Please press the arrow key up and OK for another satellite (eg Hotbird) added. Go away again to step 5. Make sure to choose the correct here Diseqc settings.
   
   Please press the arrow key up and press OK to set the satellite tuner for second Please change this, in addition to that described in Section 5 Diseqc also high on the point Tuner1 Tuner2.
   
   After you click "next" confirmed with OK looks the iCord now automatically each transponder and stores them in its internal list from. Once this is done is changing the symbol and it appears there STOP SAVE. Here you press the OK button.
   
   
   
7. software update
   The receiver will in the next step if a newer software is available via satellite. If a newer software is available, the receiver will display it and prompt you to update.
   
   
   
8. display
   Here you can choose the default display of the ICORD. Since you can change the resolution of the V-format is no change necessary.
   
   
   
9. hard disk partition
   have experienced users the ability to change the one to use space on the hard drive. Please press on "next" OK, if you do not want to change the settings.
   
   
10. Score: shows you the
    Here FOXSAT HD an overview of all settings. To exit the installation, you simply press on the already yellow shaded point "end" with the OK button.